"The water pressure is low" can mean several different things. One slow tap, every tap in the house, only the hot, or a shower that is fine at midday and weak at seven in the morning all have different causes. A few minutes of checking usually tells you which one you have.
Andrew covers Woodbridge from Halesworth. This is what he looks at first, and what you can safely check yourself before you ring.
One tap, or the whole house?
Start with the outlet that is bothering you, then try another on the same floor and one somewhere else. Run the cold, then the hot. You are finding out whether the problem follows one fitting, one temperature or the whole property.
Think about when it started, too. A sudden drop after work on the plumbing, or after the water was off in the street, points somewhere different from a flow that has faded over months.
If it is just one tap or shower
This is usually the easy one. Most taps have a small mesh filter, called an aerator, in the end of the spout. Over time it fills with limescale and grit. On many taps it unscrews by hand, and a rinse or a soak in descaler often brings the flow straight back.
Shower heads scale up the same way. If the spray is uneven or some holes have stopped, unscrew the head and soak it. If that does not help, the problem may be the shower valve or the hose, which is a job for Andrew.
Then look underneath. Many basins and sinks have small isolation valves on the pipes up to the tap. If the slot is across the pipe, it is shut; along the pipe, it is open. A valve left half shut after earlier work is a common cause of one weak tap.
If every cold tap is weak
Check the stopcock first, usually under the kitchen sink. It should be fully open, turned anticlockwise until it stops. If someone turned it down during a job and never opened it fully, that alone can do it. If it is stiff, do not force it. A seized stopcock is worth replacing anyway, before you need it in an emergency.
Then ask a neighbour. If their pressure has dropped too, the problem is probably on the supply side and your water supplier is the first call. If it is only your house, the cause can be an old, narrow or corroded supply pipe, or a leak on the pipe between the street and the house. If you have a water meter, turn everything off and watch it. If the dial still moves, water is going somewhere.
One useful test: time how long the kitchen cold tap, which comes straight off the mains, takes to fill a bucket. It turns "the pressure feels low" into something Andrew can compare with what that pipe ought to deliver.
If only the hot is weak
The cause depends on what kind of system you have.
- Combi boiler: hot flow is limited by how much water the boiler can heat at once, so it is always a little lower than the cold. If it has dropped, a blocked filter on the boiler's cold inlet or a scaled-up heat exchanger are the usual causes, and that is a boiler repair rather than a plumbing one.
- Tank in the loft and a cylinder in the airing cupboard: the pressure comes only from the height of the tank, so upstairs showers are naturally weaker. A sudden drop can mean the float valve in the loft tank is sticking, or a valve near the hot water cylinder has been left part closed.
- Unvented cylinder: these run at mains pressure through a pressure reducing valve with a small strainer, which can clog. They also need a yearly check by a qualified engineer.
What not to do
Do not force stiff valves, take a shower valve apart, or start adjusting the boiler or cylinder controls to test a theory. Changing several things at once makes it harder to tell what the original fault was. If you can see water where it should not be, in a cupboard or as a damp patch on a ceiling, turn the water off at the stopcock and treat it as a leak.
What to tell Andrew
When you ring, say which outlets are weak, hot or cold or both, whether it was sudden or gradual, what kind of system you have, and whether anyone has worked on the plumbing recently. A short video of the weak flow next to a normal tap says more than a description.
Andrew finds the cause before replacing anything, then tells you what it is and what it will cost before he starts. If it is the fitting itself, that is tap and shower work; a leak on the supply is a plumbing repair.
Questions people ask
Two that come up a lot.
Why is the water weak at only one tap?
Usually a blocked aerator or a half-shut isolation valve under that tap. If neither helps, the cartridge or valve inside the tap may be the problem.
Can you give me a price from a photo?
For a small fix, a photo and a few lines often give Andrew enough to tell you roughly what it will cost before he visits. If it is the supply pipe or the boiler, he will need to see it.
If the water in your house has gone weak, ring Andrew on 07801 988752 or send the details through the contact page.


